MITSUBISHI
Home >> Products >> MITSUBISHI >> FX series PLC >> FX all modules and accessories >> FX2N module >> FX2N-48ET-DSS Input / output module

FX2N-48ET-DSS Input / output module

MITSUBISHI FX2N-48ET-DSS Manual And Instructions
FX2N-48ET-DSS datasheetPDF datasheet

MITSUBISHI FX2N-48ET-DSS Product information and technical parameters:
Brand: MITSUBISHI
Name: Input / output module
Model: FX2N-48ET-DSS
Input and output points: 48 points.
DC power supply: DC24V.
Input points: 24 points.
Output points: 24 points.
Output form: transistor output (source).
Weight: 0.85kg.
Input signal voltage: DC24V.
FX2N series expansion unit
Expansion unit is an input and output expansion device with a built-in power supply.
As with the basic unit, the extension unit can be connected to a variety of input and output and special extension equipment.
Can connect to FX3GA/FX3G, FX3GE and FX3U.
AC power model, the built-in maximum DC24V 250mA/460mA supply power.
Because all models of FX series are built in high speed counter,
So the high speed control can be realized by the simple procedure.
The input of the basic unit is built in the anti jitter filter,
One part as digital filter,
Sensitivity adjustment unit can reach 1ms.
Using high speed counter automatically adjusted to the minimum value.
Through the high cost of the built-in positioning function and the expansion function to increase the number of control axis.
Extended function expansion board and special adapter,
Data links and communication with external serial devices.

Max input / output points: 30 points.
Supply voltage: 100 - 240VAC.
Input points: 16 points.
Output points: 14 points.
Output type: Transistor (source).
Power consumption (W): 8.
Weight (kg):0.35.
Size (WxHxD) mm:100x90x75.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types FX2N-48ET-DSS.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX2N-48ET-DSS
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O FX2N-48ET-DSS.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Input points: 8 points.
Output points: 6 points.
Power supply voltage: AC100-240V.
Output type: transistor output (source).
Built in CPU, power supply, input and output. While maintaining the convenience of FX1N while improving performance FX2N-48ET-DSS.
Special adaptor and function expansion board can be installed and used FX3 series.
High speed operation.
Basic instructions: 0.21 s/ instruction.
Application instruction: 0.5 s/ instruction.
Large capacity memory.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function. Axis of control: 1.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
7 operating modules required for easy positioning control are provided.
Type of instruction, please refer to the list in front of you.
One can control a shaft.
FX3U, PLC FX2N can connect up to 8 units,
PLC FX2NNC can connect up to 4 units,
PLC FX3UC can connect up to 7 units, so that it can control more than one independent axis FX2N-48ET-DSS.
Maximum can output 100kHz pulse train.
Positioning control through the control program. Function: RS-232C communiication FX2N-48ET-DSS.
CPU module connected to the front of the expansion function of the substrate.
The front of the CPU module can be connected to 1 units at most.


...More relevant models >>>>